CAS 7440-05-3 Pd nanopowder Ultrafine Palladium as catalyst
Size:20-30nm Purity:99.95% CAS No:7440-05-3 ENINEC No.:231-115-6 Appearance:black Powder Shape:spherical
13929258449
Size:20-30nm Purity:99.95% CAS No:7440-05-3 ENINEC No.:231-115-6 Appearance:black Powder Shape:spherical
We can supply different size products of niobium silicide powder according to client's requirements. Size:1-3um; Purity:99.5%;Shape:granular CAS No:12034-80-9;ENINEC No.:234-812-3
Ni2Si particle,99.5% purity,granular shape,is used for Microelectronic integrated circuit, nickel silicide film,etc. Size:1-10um; CAS No:12059-14-2;ENINEC No.:235-033-1
Size:5nm | Purity:99.9% | CAS No:13463-67-7
ENINEC No.:215-280-1 | Type:Anatase
Appearance:white and light yellow Powder
Brand:
SAT NANOItem NO.:
OP2208B-5nmPayment:
TT, Paypal, WUProduct Origin:
ChinaColor:
White PowderShipping Port:
Shenzhen, ShanghaiLead Time:
1-5daysMin Order:
1kg
Active Photocatalyst Nano Titanium Dioxide 5nm
Specification of Active Photocatalyst Titanium Dioxide:
Part No. | Particle |
Purity (%) |
SSA (m2/g) |
Bulk density (g/cm3) |
Density (g/cm3) |
Crystal | Color |
OP2208B-5nm | 5nm | 99.9 | 220 | 0.25 | 3.9 | anastase | white |
The particle size is very small: about 5 nanometers.
Good dispersing performance: 5 nanometer titanium dioxide has good dispersing performance and can self-disperse into pure water without stirring. It can be sprayed on the furniture surface and wall to form a uniform nano-coating, which plays a role in purifying indoor air.
High catalytic activity: The catalytic activity of this nano titanium dioxide has been tested to capture and degrade harmful gases such as formaldehyde, benzene and ammonia in the room.
How to use: Dissolve 100g of powder into 10kg of pure water, or distilled water, deionized water, etc., make a 1% solid solution, spray it directly on walls, home surfaces, and car interiors.
Notes for use:
1. Note that it is recommended to use imported spray guns with a caliber of 0.5mm-1mm for indoor dark furniture and high-finish furniture. Spraying should be performed uniformly and uniformly during spraying, and no sagging or unevenness can occur.
2. It is recommended not to spray metal stainless steel and other parts, and do protection before construction.
3, furniture construction mainly deals with the rough surface of the furniture, the side, back, inside and bottom of the furniture.
4, wallpaper is recommended to use 0.5% or lower spraying, or not spraying.
5. Do not spray on the human body. If sprayed on the eyes, wash it with running water.
6. When spraying, if the distance from the spraying surface is too close, the spraying fluid will flow and leave marks; if the distance from the spraying surface is too far, white spots or reduced adhesion will occur. Therefore, observe the spray distance in accordance with the construction specifications.
7. After spraying the JR05 photocatalyst, use clean water to clean the spray equipment to prevent nozzle clogging and corrosion.
8. When the product solution is sprayed onto other objects than the sprayed surface or flowing onto other objects during construction, wipe them off in time.
9. If there is moisture, spray after fully drying. The sprayed surface should not be in contact with water within 2 hours after spraying.
10. Avoid construction in confined spaces and fully ventilate after construction.
11,100m2 building area, it is recommended to use 100g of photocatalyst powder, the specific amount is determined according to the situation of exceeding the standard
12, should wear protective goggles, long-sleeved trousers, masks, gloves and other protective equipment during construction.
SEM & XRD of Active Photocatalyst Titanium Dioxide:
Storage conditions:
Active Photocatalyst Titanium Dioxide should be sealed and stored in a dry and cool environment.
It should not be exposed to the air for a long time, to prevent agglomeration due to moisture, affecting the dispersion performance and use effect, and should avoid heavy pressure, do not contact with oxidant, and transport according to ordinary goods.